Lee 6 Cav Mold w/ Handles & Size and Lube Kit for 44 Spec/44 Rem Mag NEW! 90227

Description

Lee 6 Cavity Mold with Handles and Sizing and Lube Kit Combo
90227+90005+90062+90177
44 Special / 44 Rem Magnum / 44-40 WCF
(430 Diameter) 310 Grain Flat Nose Gas Check
NEW!!
90227
430-310-RF
Designed for volume production, the Lee 6-Cavity Bullet mold
blocks are machined from commercial quality aluminum and
feature steel bushing and alignment pins.
Lee mold blocks are machined from aluminum blocks making
making them rust resistant.
Aluminum molds heat up and cool down faster than iron or
steel molds so good bullets can usually be produced after only
a few casts.
In addition, they are one-third the weight of iron or steel mold
blocks for less fatigue during extended casting sessions.
To ensure the best possible bullets, mold block halves are CNC
machined for unmatched roundness and size control.
Lee 6-Cavity molds come with a cam operated, hard-anodized
sprue plate which is held tightly with tempered spring washers
at each end.
Weights given are Lee's weights with suggested alloy; actual
weight may vary due to alloy mixture used.
Material:
Machined Aluminum Mold Blocks and Hard Anodized Sprue Plate
Cavities:
6
Features:
Rust resistant aluminum blocks.
Lathe bored blocks with steel bushings & aluminum pins.
For TWO cavity mold order ebay item number,
221230230675
+
90005
Commercial Mold Handles
for 6-Cavity Lee Mold
New
Lee Commercial Bullet Mold Handles for 6-Cavity Bullet
Molds
are necessary for using Lee 6-Cavity molds which do
not ship
with handles.
These handles also fit the Lee 18 Cavity Buckshot molds.
This handle has a steel frame and hardwood grips which are
designed
to last a lifetime.
Material:
Hardened Steel frame, Hardwood gripped
Fits:
Lee 6-Cavity and 12-Cavity Bullet Molds
+
Bullet Lube and Size Kit
430 Diameter
New
90062+90177
The Lee Lube and Size Kit is one of the fastest and easiest ways
to lubricate and size cast bullets.
The sizing die that comes with the kit fits in any press that accepts
standard 7/8"-14 threaded dies.
Bullets are pushed through the sizing die nose first, so no special top
punches are needed.
Gas checks are automatically seated and crimped in place.
Sized bullets are captured in the special container and a 4 oz bottle of
Lee Liquid Alox bullet lube is included.
Material:
Hardened Steel Sizing Die, Plastic Hopper
Function:
Size cast bullets
Notes:
Comes in red plastic case.
Lee recommends bullets be re-lubed after sizing to be sure the sized
portion is coated with Alox.
All lead bullets must be lubricated, but it is not absolutely necessary
to size all cast bullets.
Bullet must be sized if they are so large that they expand the case too
much to freely enter the gun's chamber.
Sizing sometimes helps accuracy by making the bullet uniform in
diameter.
Sizing helps insure uniform start pressure and better accuracy.
Gas checks can be installed with this tool.
Simply place the gas check on the base of the bullet before sizing.
Directions for Use:
Lubricating Bullets:
1.
Place bullets in provided red plastic container and drop in the included.
Lee Liquid Alox onto the bullets.
2.
Gently shake the bullets in an orbital motion to coat the bullets.
If they do not coat completely, add a little more lube.
3.
Spread the bullets onto waxed paper and let dry overnight.
4.
Load at least one bullet into a case and check to be sure it easily chambers
in the gun.
If it fits tightly, you must resize the bullet before loading.
Directions for Use:
Sizing Bullets:
1.
Screw the sizing die into any standard reloading press.
Exact depth is not important.
2.
Install the bullet punch into the ram.
This fits all rams that use standard shellholders.
3.
Place the red plastic container with the lubed bullets inside
on top of the sizing die.
4.
Place bullet on the punch and push the bullet through the die.
5.
When 3/4 of the bullets have been loaded, lift the red plastic
container
off the die.
Invert the holder before opening.
6.
For rifle and hot pistol loads, it is best to re-lube the bullets to
ensure the sized portion is re-coated.
~~~~~~~~~~~~~~~~~~~~~~~~~~
We are a Factory Direct Dealer of
Lee
®
Precision, Inc.
ALL MANUFACTURERS WARRANTIES WILL APPLY !
All of our products are
BRAND
NEW
in the box; and contain all of the parts,
materials and documentation.
You can expect and will receive prompt delivery of your item.
We will ship your order within
ONE DAY!